Use this all-in-one unit by placing it fully submerged in the pond and choosing whether you want it running as a filter, a pump, or as a fountain feature alongside filtration. It combines the pump, UVC steriliser and filter media in one compact body, so the layout stays simple when setting it in position.
✓ 13W UVC steriliser✓ Submersible unit✓ Foam filter✓ Fountain kit included✓ Waterfall outlet✓ Ponds up to 15000L✓ Fish ponds up to 7500L✓ Flow control T-piece
Suitable for ponds with a mix of small fish up to 7500 litres and for ornamental ponds up to 15000L, the compact size of the unit allows it to be discreetly positioned fully submerged in your pond.
The Latest Technology All in One Pond Filter Pump
This pump has an extensive filtration area to help collect dirt and debris from your pond. Designed to provide filtration within one unit, you can also use the 15000 as a water pump or fountain at the same time.
Filtration can be achieved in 3 ways
Mechanical (Foam)
Large foam filter inside the unit
Removes solids up to 7 mm
Optional extra filtration
Bolt-on filtration increases capacity
UV clarification
UV helps clump green algae
Ready for collection
Use the 15000 Filter Pump as a Waterfall or Fountain at the same time
Connect tubing to the pump and create a waterfall cascade. The pump has a hose tail outlet to attach 20 - 25 mm garden tubing and has a max head of 2 meters. Also includes a T Piece to divert and control waterflow.
Use the 15000 Filter Pump as a Fountain Feature
A fountain kit is included with the TripleAction 15000, so you can enjoy a fountain spray effect simply by attaching a fountain head of your choice (3 different heads included).
This is a professional-level filter pump designed to help keep a fish pond clean with minimal maintenance involved. It is mains powered and straightforward to set up.
Place unit at bottom of pond – preferably on a level surface raised approx. 10cm from floor (eg, upturned plant pot or clay brick) with outlet facing upwards.
Once installed the pond water will flow through the pump as the pump’s impellor draws in water. It is always best to position your pump at the opposite end to where the water returns to the pond to provide maximum circulation.
Your unit is supplied with a hosetail. Pond hose size 20-25mm can be attached to the inlet hosetail. Cut the inlet hose to the size appropriate to the size of hose you are using. Then connect the hose from your pump to your filter system or position it where you want the water to return. Ensure a watertight seal by the use of hose clips.
Maintenance
Occasionally large solids may block the holes in the filter cage surrounding the pump – these should be carefully wiped away. A clogged or dirty intake will put a strain on the motor and greatly reduce its performance. If the area where the pump is stood is very dirty, raising its position slightly will assist flow. To clean the pump, remove the impellor housing and impellor. Use clean water and a small brush to remove debris (see below)
Changing the UV Bulb / Maintenance of the unit
A UV indicator around the body of the unit lights up to shown UV is working. If it doesn’t light up, or if the bulb has been used for over 6 months you will need to change the UV bulb inside the unit. To open the unit up, first disconnect from power supply and lift clear of water.
Remove backing plate with a cross head screwdriver then around the middle of the unit there are two push clips – hold these in then pull the main body apart. The foam is now accessible and can be cleaned if required. Access the impeller by again pressing the two clips around the top in and pulling the top case away from the main unit. Turn the impellor guard to gain access to the impellor and clean if required. The UV bulb can be accessed by unscrewing the screw located in the base of the remaining black casing. Turn the casing as indicated by the two arrows on the casing
Limited Warranty
This product is guaranteed for a period of 12 months (excluding rotor assembly) from the date of purchase for material or manufacturing defects. The guarantee covers the substitution of defective parts. However, the guarantee is considered null and void in the case of improper use, improper handling or negligence on the part of the buyer. If your pondXpert pump fails please take it back to the retail outlet from where it was purchased. You will be required to take your receipt/proof of purchase with you. This does not affect your statutory rights.
